AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateCarrier Ductwork Repair: The Henderson Owner’s Guide
Carrier ductwork repair in Henderson typically runs $150 – $650 installed, depending on whether we’re resealing a leaking joint, replacing a run of flex duct, or rebuilding a plenum connection at the air handler, and most jobs are done the same day we come out. Your Carrier equipment itself is usually fine. What fails is the network carrying the air: torn flex duct in an attic that hits 150°F in July, crushed runs behind a remodeled closet, or tape that dried out and let go years ago. Owners usually find out one of three ways: a room that never cools no matter what the thermostat says, a whistling sound at a supply register, or dust streaks around the grille where air has been leaking into the ceiling.
Which Carrier Models This Applies To
Ductwork isn’t brand-proprietary the way a control board is, but Carrier’s installed systems in Henderson fall into a few recognizable families and each one has its own supply and return sizes. Carrier Comfort and Performance series air handlers typically use a specific plenum opening size (the rectangular mouth where duct attaches to the unit), and if that opening doesn’t match the transition, you get turbulence, static pressure loss, and a system that runs longer than it should. Infinity and Evolution series units often sit on variable-speed blowers that are far less forgiving of undersized or leaking duct than an older single-speed unit was – a leak that was tolerable in 2010 now shows up as a hot bedroom.
To match the right part, we look at the data plate on the indoor unit (model and serial), measure the actual duct collar and boot sizes at the register, and check whether the existing runs are rigid galvanized, fiberboard, or flex. OEM Carrier transitions and plenums are the cleanest fit when the original cabinet is still in place. Quality aftermarket equivalents in the same gauge and R-value are a sound choice for the runs themselves, and often the better value when a whole branch needs replacing. We’re an independent service provider, not affiliated with Carrier, so we quote what actually fits your cabinet rather than what’s in a brand catalog.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Signs Your Carrier Ductwork Repair Is Failing
- Uneven cooling room to room. A torn or disconnected flex run is bleeding conditioned air into the attic before it reaches the register. The system works harder and one side of the house never catches up.
- Whistling or roaring at a supply register. That sound is usually a crushed or undersized duct forcing air through too small an opening. It’s a sign the run needs resizing, not just resealing.
- Dust streaks around grilles and ceiling stains. Filtered air shouldn’t leave a trail. Streaking means air is escaping at the joint and pulling attic dust with it – a classic Nevada attic symptom.
- Higher bills with no obvious cause. Leaking duct in a 140°F attic can lose a meaningful share of your cooling before it ever reaches a room. You pay to cool the attic.
- Rattling or sagging duct in the attic. Flex duct that has lost its support straps sags, pinches, and restricts airflow. Left alone it eventually tears at the collar.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed ductwork repair in Henderson lands in the $150 – $650 range for the work most owners actually need. Here’s what drives the number:
- Reseal and repair a joint or boot: $150 – $280. Mastic and proper tape, not the cloth duct tape that failed in the first place.
- Replace a single flex run: $220 – $420. Includes new insulated duct, straps, and reconnection at both ends.
- Plenum or transition rebuild at the air handler: $350 – $650. Sheet metal work sized to your Carrier cabinet.
Every price is written down before a tool comes out, and it doesn’t change at the door. If you have us out for a tune-up at the same visit, that flat rate runs $80 – $200 and covers a written report of what we actually found. This repair is covered for 365 days under our Done Right Promise: if it fails, we come back and fix it at no charge.
DIY or Call Us?
You can safely do a few things yourself. Look at the visible duct in the attic with a flashlight and check for disconnected runs, sagging, or torn flex. Feel around the register boots for air leaking into the ceiling. Change the filter. What you shouldn’t do is climb into a Henderson attic in July to reseal or rework duct – attics here regularly exceed 140°F, and heat illness in an attic is real, fast, and quiet. Add the sharp sheet-metal edges, the risk of stepping through ceiling drywall, and the fact that a bad mastic job just leaks again next summer, and the math points one way. Call us at (844) 797-5122 and we’ll send a background-checked technician in a written arrival window.
FAQs
Flex duct in a Henderson attic typically lasts 10 – 15 years before the outer jacket cracks and the inner liner tears, which is shorter than in milder climates because attic heat and UV exposure break down the jacket faster. Rigid galvanized duct can last decades if the joints were sealed properly. If your home’s duct is original to a mid-2000s build, it’s worth a look.
Yes, most of the time. A single disconnected run or a failed joint is a repair, not a replacement, and that’s the $150 – $280 end of the range. Whole-house duct replacement only makes sense when the runs are collapsing or the system was undersized from day one. We tell you which one you’re looking at before any work starts. Call (844) 797-5122 for a written price.
A single run or joint repair usually takes one to two hours on site. A plenum rebuild or multiple runs can take most of a visit. Because we answer the phone with a live person 24/7, you can get a firm arrival window today rather than waiting for a callback.
We match by the model and serial on your indoor unit and by measuring the actual duct connection, then source OEM Carrier transitions where fit matters and quality aftermarket duct where it doesn’t. We don’t carry stock on the truck, so the part is ordered to your system, not guessed. The phone is answered around the clock – call (844) 797-5122 for a free estimate.
Air leaking into your Henderson attic is money leaking out of your wallet every month the system runs. Whether it’s a torn flex run, a dried-out joint, or a transition that never fit right, we’ll show you exactly what’s wrong, hand you the price in writing, and back the work with our 365-Day Done Right Promise. Our technicians have up to 23 years of experience and are trained across nine major brands, including Carrier, Trane, and Lennox. Call Coldharbour Heating & Air Henderson at (844) 797-5122 for a free estimate.
Written by the team at Coldharbour Heating & Air Henderson, serving Henderson and nearby areas.