AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateLennox Furnace Repair in Henderson: What to Know First
We repair Lennox furnaces in Henderson, and most jobs are finished in a single visit: diagnostics on arrival, a written price in your hand before any tool comes out, and the repair done the same day in the large majority of cases. Typical Lennox furnace repairs run $150 – $700, and the price we quote at the door is the price you pay. No surprises, no “it was more complicated than we thought” phone call from the driveway.
This page is for Henderson homeowners who already have a Lennox furnace in the garage or utility closet and need it working again. We’re an independent Lennox service provider, not affiliated with or authorized by Lennox, so we have no reason to sell you a new unit when a repair will do. Call (844) 797-5122 and a live person picks up, day or night.
How Lennox Products Fail – and How We Fix Them
Lennox builds solid equipment, but every line has its patterns. After years of working on these systems in Henderson homes, we know where to look first.
- Elite Series high-efficiency furnaces and their pressure switches. The EL296V and similar condensing models use a pressure switch to prove the inducer is moving exhaust. In Henderson, where the air is dry and dusty and our short, mild winters mean the furnace sits idle for months, that switch and its port can gum up or collect debris. The furnace short-cycles or refuses to light. We test the switch and clear the port, and when the switch itself has failed we replace it rather than bypass it.
- Merit Series igniters that crack quietly. The ML195 and ML196 are common in Henderson tract homes built in the 2000s. Their silicon nitride hot-surface igniters are tough but brittle, and a cracked igniter is the single most common no-heat call we run on these units. You’ll hear the inducer start and then nothing – no flame, no heat. Replacement is usually a same-day job.
- Flame sensors that read “dirty” after a dry summer. Lennox uses a flame sensor to confirm the burners actually lit. Our low humidity and long cooling season let a thin oxidation film build on the sensor rod. The furnace lights, runs a few seconds, then shuts down as a safety measure. Cleaning or replacing the sensor restores normal operation, and we check the whole ignition sequence while we’re in there.
- Inducer motor bearings on older units. The draft inducer on a 15-year-old Lennox will start to whine or grind before it seizes. That noise is your warning. We replace the motor before it takes the control board with it, which is a far cheaper repair than the alternative.
- Cracked heat exchangers on high-hour systems. This is the one we take most seriously. A cracked heat exchanger can let combustion gases into the supply air. We inspect it with a camera on any furnace old enough to warrant it, and we tell you plainly what we find. Do not run a furnace you suspect has a cracked heat exchanger – that’s a carbon monoxide risk, and it needs a trained technician, not a DIY fix. If the exchanger is compromised, we’ll walk you through repair versus replacement honestly.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Our Lennox Furnace Repair Process
Here’s exactly what happens from the moment you call to the moment we leave.
- 1
You call and a live person answers. No voicemail tree, no “leave a message and we’ll get back to you.” We book a firm arrival window and put it in writing.
- 2
We diagnose on arrival. The technician pulls the fault codes, tests the ignition sequence, and confirms the actual failure before recommending anything.
- 3
You get a written price before work begins. Parts and labor, itemized, handed to you before a single tool comes out. It doesn’t change at the door.
- 4
We make the parts call. For Lennox we lean toward OEM parts when they’re available and the price makes sense, because they fit right and keep your existing warranty intact. Where a quality aftermarket part is a better value and warranty-safe, we’ll say so and explain the trade-off.
- 5
We repair and test. The fix goes in, then we run a full heat cycle – ignition, blower, temperature rise, the works – so we know it’s right before we pack up.
- 6
We leave it cleaner than we found it and hand you the guarantee in writing. Every repair is covered by the 365-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Lennox Furnace Repair Costs in Henderson
These are the ranges Henderson homeowners actually see for Lennox furnace work. Your written estimate is exact before we start.
| Repair | Typical Range |
|---|---|
| Igniter replacement | $150 – $280 |
| Flame sensor clean or replace | $150 – $250 |
| Pressure switch / inducer port | $200 – $400 |
| Gas valve repair | $300 – $600 |
| Blower motor repair | $350 – $700 |
| Furnace tune-up | $80 – $200 |
What moves the price: the parts decision (OEM versus aftermarket), how deep the technician has to go to reach the failed component, and whether a secondary issue turns up during testing. We tell you about all of it before we touch anything. Estimates are free.
Why Henderson Homeowners Call Coldharbour Heating & Air Henderson for Lennox Work
Our technicians have up to 23 years of experience, and they’re trained on nine major brands including Lennox – so the person who shows up can work on your system whether it’s a Lennox, a Carrier, a Trane, or something else. Every technician is background-checked and uniformed, so you know exactly who’s at your door. You get a written price before work starts and a written guarantee before we leave: if the repair fails within 365 days, we come back and fix it at no charge. That’s the Kingswell Way, and it’s why homeowners who’ve been burned by a no-show or a price that jumped call us instead. Phones are answered around the clock, every day.
FAQs
It can, and that’s why it matters who does the work. Using OEM Lennox parts and following the manufacturer’s procedures keeps your factory warranty intact. Because we’re an independent Lennox service provider, we make the parts call with your warranty in mind and tell you when an aftermarket part could affect coverage. Call (844) 797-5122 and we’ll walk through it before any work starts.
Yes – most common Lennox parts like igniters, flame sensors, and pressure switches are available for same-day or next-day repair. Less common components sometimes need ordering, and we’ll tell you the timeline and price up front. Estimates are free.
Repair usually wins when the furnace is under about 15 years old and the repair is a normal component failure. Replace when you’re facing a cracked heat exchanger on an aging unit, or repeated repairs that add up past the cost of a new system. We’ll give you both numbers honestly. Call (844) 797-5122 for a straight answer.
Most Henderson furnace repair calls are handled same-day, and a live person books your firm arrival window right when you call – phones are answered 24/7, no voicemail runaround. Call (844) 797-5122 for today’s availability.
Every repair we make is covered for a full 365 days. If the repair fails inside that window, we come back and correct it at no charge – the guarantee is written down before the technician leaves. No argument, no extra fee. Call (844) 797-5122 to book.
When your Lennox furnace quits, you don’t need a sales pitch – you need a straight price, a firm window, and a guarantee in writing. Call Coldharbour Heating & Air Henderson at (844) 797-5122 for a free estimate, and we’ll get your heat back on.
Written by the team at Coldharbour Heating & Air Henderson, serving Henderson and nearby areas.