Furnace & heating
AC repair
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateStyles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
See the difference
Before
After
Before
After
Before
AfterFurnace Repair in Henderson, NV
Most furnace repairs in Henderson run $180 – $420, and the majority are finished in a single visit the same day you call. We handle the diagnosis, hand you a written price before any tools come out, and back the repair with a written 365-day guarantee. If the fix fails inside that year, we come back and make it right at no charge.
That matters in a city where the heating season is short but the nights are cold. Henderson sits at roughly 1,800 feet against the McCullough Range, and desert nights between December and February drop into the 30s fast. Furnaces here don’t get the gradual workout a Midwest system does. They sit idle for ten months, then get called on hard during the first cold snap, which is exactly when tired igniters and dirty flame sensors show their age.
Coldharbour Heating & Air Henderson is an independently operated member of the Kingswell network, and we work to The Kingswell Way: say the price before the work, show up in the window given, leave the place cleaner than we found it, put the guarantee in writing, and come back if it fails. A live person answers our phone around the clock. To reach one now, call (844) 797-5122.
Our technicians have up to 23 years of experience and are trained to service nine major residential HVAC brands, including Carrier, Trane, Lennox, and Goodman, so whoever shows up can work on the system that’s already in your house.
Key Takeaways
- Most Henderson furnace repairs cost $180 – $420 and are done same day.
- You get the written price before any work starts, and it doesn’t change at the door.
- Every repair carries a written 365-Day Done Right Promise.
- Background-checked technicians, live phone coverage 24 hours a day, 7 days a week.
When You Need Furnace Repair
Furnace trouble in Henderson usually announces itself in one of a handful of ways. Here’s what we hear most, and what it usually points to:
- You wake up to a cold house. The thermostat is calling for heat and nothing happens. This is often a failed igniter or a tripped safety switch. Modern furnaces use a hot-surface igniter (a small ceramic part that glows to light the gas) and that part simply wears out over time.
- The furnace clicks, then gives up. A repeated click-and-shutdown cycle commonly means a dirty flame sensor, the rod that confirms a flame is actually burning before the gas valve stays open. It’s a common, low-cost fix.
- You smell gas, or smell something odd near the unit. If you smell gas, leave the house and call your gas utility immediately before calling anyone else. A faint musty or burning-dust smell on the first use of the season is normal; a strong chemical odor is not, and the system should be shut off and checked.
- The blower runs but the air comes out cool. That points to a problem in the ignition or gas train, or to a control board issue. On a dual-fuel system it can also mean the system is stuck in heat-pump mode.
- Short cycles and higher gas bills. A furnace that starts and stops every few minutes (short cycling) is usually straining against a clogged filter, a restricted vent, or an oversized or failing component. In Green Valley and Anthem we often see filters that haven’t been changed since spring, because the AC ran all summer.
- Loud banging, screeching, or rumbling. Screeching is often a failing blower motor bearing. Banging on startup can signal delayed ignition. Both warrant a look before they worsen.
If you recognize your furnace in any of this, don’t wait for it to fail on the coldest night of the year. Call (844) 797-5122 and we’ll get a technician out.
Our Furnace Repair Process
Here’s exactly what happens from the moment you call to the moment we leave:
- You reach a live person. No voicemail tree, no after-hours runaround. We confirm a firm arrival window and stick to it.
- A background-checked, uniformed technician arrives in that window. You’ll know who’s at your door before you open it.
- We diagnose the actual fault. That means testing the ignition, flame sensor, control board, blower, and gas components as needed, not guessing at the most expensive part.
- You get the price in writing before any work starts. The number we hand you doesn’t change at the door. If you choose not to proceed, that’s fine.
- We make the repair and clean up. We leave the workspace cleaner than we found it.
- You get the written guarantee before we leave. Every repair is covered for 365 days. If it fails in that window, we return and fix it free.
Furnace Repair Pricing in Henderson
Furnace repair pricing depends on the part and the labor involved. Below are honest ranges from what we actually see on Henderson jobs, parts and labor included. Your written price is confirmed at the door before work begins.
| Repair | Typical Range | What It Covers |
|---|---|---|
| Igniter replacement | $150 – $280 | New hot-surface igniter, testing, labor |
| Flame sensor cleaning or replacement | $120 – $220 | The rod that confirms flame; common cause of short cycling |
| Blower motor repair or replacement | $350 – $650 | Motor, bearings, labor; variable-speed units trend higher |
| Control board replacement | $300 – $600 | Circuit board, diagnostics, labor |
| Gas valve replacement | $350 – $700 | Valve, safety testing, labor |
| Inducer motor / draft assembly | $400 – $700 | The motor that pushes exhaust out; high-efficiency units |
What moves the number: the brand and age of your system, whether the part is under warranty, and how accessible the unit is. A high-efficiency condensing furnace has more parts than a standard 80% unit, and a unit tucked into a tight attic space in a Henderson home takes longer to service than one in a garage. Homes built during the 2000s boom in communities like MacDonald Ranch and Seven Hills often have the original furnace, so parts for a 15-to-20-year-old unit can be harder to source.
What we won’t do is hand you a vague estimate and change it once the tools are out. The Kingswell Way is price before work, every time. Estimates are free. Call (844) 797-5122 to schedule one.
Two safety notes worth stating plainly. Furnace ignition and gas components are dangerous to handle without training, and we don’t recommend troubleshooting the gas train or ignition yourself. If you smell gas, leave the home and call your gas utility first. For everything else, leave the repair to a trained technician.
FAQs – Furnace Repair
How much does furnace repair cost in Henderson, NV?
Most furnace repairs in Henderson cost $180 – $420, with the exact number depending on the part. An igniter or flame sensor fix sits at the low end, while a blower motor or gas valve falls at the higher end. You’ll get a written price before any work starts. Call (844) 797-5122 for an exact quote, and the estimate is free.
Can you come today?
In most cases, yes. We schedule same-day furnace repair across Henderson when you call, and a live person answers the phone around the clock, so you’re not waiting until morning to reach someone. Call (844) 797-5122 and we’ll give you a firm arrival window.
Is it cheaper to repair or replace my furnace?
Repair usually wins if the unit is under about 15 years old, the repair is a single common part, and the system is otherwise sound. Replacement starts to make more sense when the furnace is past 15 – 20 years, needs repeated repairs, or the repair cost approaches half the price of a new unit. During a free visit we’ll tell you honestly which makes sense for your system. Call (844) 797-5122 to talk it through.
What does your guarantee actually cover?
Every repair we make is covered for 365 days. If the same repair fails inside that year, we come back and correct the work at no charge. It’s written on paper and handed to you before the technician leaves, not offered verbally. Call (844) 797-5122 to schedule service covered by that promise.
Contact Coldharbour Heating & Air Henderson
Henderson homes don’t need much heat, but they need what they get to work. Whether your furnace is clicking, blowing cold, or just making a noise you can’t place, call Coldharbour Heating & Air Henderson at (844) 797-5122 for a free estimate. You’ll get a firm arrival window, a written price before the work starts, and a written 365-day guarantee on the repair. If our work fails inside that year, we come back free. That’s The Kingswell Way, and it’s how we do furnace repair in Henderson. For related help, see our overview of our home heating and cooling services, or explore Heating & Furnace in Henderson for broader system questions.
Written by the team at Coldharbour Heating & Air Henderson, serving Henderson.