AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateLennox Ductwork Repair: The Henderson Owner’s Guide
We repair Lennox ductwork in Henderson for a typical installed cost of $185 to $640, depending on the failure, and most jobs are handled the same day you call. If a supply run has torn apart in an attic or a return duct has collapsed under a mobile home, we can usually have air moving correctly again within hours. Lennox makes solid equipment, but ductwork fails on its own schedule: heat, dry air, and the way flex runs were hung during the original install all take a toll.
Owners usually spot the problem in one of two ways. Either a room that used to cool fine now runs warm no matter what the thermostat says, or there’s a whistling or flapping noise coming from the attic or crawlspace when the blower kicks on. A few notice it on the bill first; the system runs longer and the number climbs before anything feels wrong inside the house.
Which Lennox Models This Applies To
Ductwork isn’t tied to a specific Lennox model the way a control board or a heat exchanger is. The duct system is sized to the air handler and the house load, so it works with anything from an older Lennox 10ACX condenser paired with a variable-speed air handler to a newer Lennox Elite series system. What matters is the static pressure the blower is designed to push against, the supply and return trunk size, and the branch takeoff diameter feeding each room. Common branch runs here are 6-inch flex, with 8-inch trunks; the exact sizing needs to match your air handler’s rated CFM, not just the old duct that failed.
The right way to match a part is to measure, not guess. Pull the data plate off the air handler or look at the outdoor unit’s model tag, note the tonnage, and measure the inside diameter of the existing duct takeoff you’re replacing. Flex duct, rigid pipe, and insulated sheet metal all have specific fit dimensions, and a replacement piece has to seal to those dimensions to hold the system’s efficiency. We work with both Lennox OEM duct components and equivalent aftermarket flex and fittings that meet the same specs at a lower price point, and we tell you which is which before we order. We’re an independent service provider, not affiliated with Lennox, so there’s no incentive to steer you toward a branded part that costs more without buying you anything.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Signs Your Lennox Ductwork Repair Is Failing
Lennox ductwork fails in specific, recognizable ways, and knowing which symptom you’re seeing points directly at the repair. Here’s what to check:
- Rooms that won’t cool evenly. A torn branch run or a duct that’s come loose at a takeoff dumps conditioned air into the attic instead of the bedroom. This usually shows up as one or two rooms that stay hot while the rest of the house feels fine.
- Whistling or flapping at the vents. Flex duct that’s collapsed, kinked, or torn open causes blower turbulence that you hear at the register. A flapping sound often means the inner liner has separated and is slapping against the outer jacket.
- Higher power bills with no other change. When ductwork leaks or collapses, the system runs longer to satisfy the thermostat. A 20 percent duct leak can add real dollars to a Henderson summer bill before you notice anything inside the house.
- Dust blowing out of registers after the system starts. A cracked return duct pulls attic air, insulation fibers, and dust into the airstream and pushes it into the living space. This one usually gets noticed first because it’s visible.
- Condensation or water stains near the air handler or in the attic. A leaking duct in a Henderson attic during summer pulls humid outside air into the cold airstream and sweats. Insulation damage from that moisture compounds the problem quickly.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Most Lennox ductwork repairs in Henderson fall in the $185 to $640 range, installed, parts and labor included. Here’s what actually moves the number:
| Scope | Typical Installed Range |
|---|---|
| Single branch duct reconnection or replacement | $185 – $300 |
| Supply or return trunk section replacement | $280 – $450 |
| Multiple branch runs plus sealing at plenum | $380 – $640 |
| Full flex system replacement (small home) | Quoted separately, likely above repair range |
The price you’re given is written down before any tool comes out, and it doesn’t change at the door. Labor covers the diagnostic, the removal of the failed section, the new material, and sealing and testing the repair. Every duct repair we do is backed by the 365-Day Done Right Promise. If the repair fails inside 365 days, we come back and make it right at no charge, and that guarantee is on paper before we leave. Live duct repair pricing above the AC repair range of $150 – $650 will be quoted in writing before we start.
DIY or Call Us?
Replacing a section of flex duct in a Henderson attic in July is not a job we recommend taking on yourself, and not because the material is expensive. Attic temperatures here regularly run past 130 degrees in summer, the space is tight, and getting a duct connection to seal properly requires the right tape, mastic, and tension. A loose or poorly sealed duct you install yourself will leak, and you’ll have spent a hot afternoon on it for nothing.
What you can safely do: check your filter, confirm the vents are open, look at the thermostat, and note which rooms are affected. Turn the system off before you climb into an attic or crawlspace, and don’t try to reconnect a duct at the air handler plenum while power is live. If you’ve done the basics and the system still isn’t right, that’s where we come in. Give us a call at (844) 797-5122, and we’ll give you a written price before any work starts.
FAQs
Most flex ductwork in southern Nevada lasts 12 to 18 years before it starts failing, shorter than in milder climates because attic heat degrades the inner liner faster. Direct sun on a duct run, rodents in the attic, and a poorly sized original install all shorten that window. If your system’s original ductwork is more than a decade old and you’re seeing any of the symptoms above, it’s worth an inspection.
Yes, and that’s what we aim for. A single torn or disconnected branch is usually a repair, not a replacement. Full replacement is only the right call when the majority of the runs have failed or the original sizing is wrong. Call (844) 797-5122 and we’ll tell you honestly which one you’re looking at.
Most single-run repairs take 1 to 2 hours once the technician is on site. A multi-branch job runs 3 to 5 hours. We give you a firm arrival window and hold to it, and you’ll have a written price before work begins.
We measure the existing duct and match the replacement to your air handler’s model and the takeoff dimensions, working with both Lennox OEM components and equivalent aftermarket material. We don’t carry parts on a truck or stock Lennox parts locally. We confirm the right part before we order, and we tell you which option you’re getting and why. We service Lennox systems alongside Carrier, Trane, and other major brands, and our technicians have up to 23 years of experience.
If your Lennox system is moving less air than it used to, the sooner you get it looked at, the less you’ll spend on the problem and the more comfortable your Henderson home will be. Call Coldharbour Heating & Air at (844) 797-5122 for a free estimate. We answer with a live person any hour of the day, we’ll give you a written price before we touch a single duct, and the repair comes with a 365-Day Done Right Promise in writing.
Written by the team at Coldharbour Heating & Air Henderson, serving Henderson and nearby areas.