A Coldharbour company - serving Henderson, NV

Trane Furnace Repair in Henderson, NV

AC repairAC repair
Furnace & heatingFurnace & heating
Heat pumpsHeat pumps
Ductless mini splitsDuctless mini splits
CarrierCarrier
TraneTrane
GoodmanGoodman
Every visit starts with

Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed

We have financing partners for your new heating and cooling system*On approved credit; ask us about your options

Diagnosis first, numbers second - you approve the repair price before a single part goes in.

Get your free estimate

Trane Furnace Repair in Henderson: What to Know First

We repair Trane furnaces in Henderson as an independent Trane service provider, and most jobs are diagnosed and fixed on the first visit, usually within 24 to 48 hours of your call. Expect to pay somewhere between $150 and $700 for a typical Trane furnace repair, with a written price in your hands before any tool comes out of the van. If you own a Trane and your heat has quit, call (844) 797-5122 and a live person will answer, day or night.

Call (844) 797-5122

This page is for Trane owners specifically: the XR80 and XR90 single-stage units that went into a lot of Henderson homes, the S9V2 and S9X2 variable-speed furnaces, and the older XV80 and XL90 models still running in neighborhoods like Green Valley and Anthem. We’ll cover what actually fails on these units, what the repair costs, and how our written guarantee works. Coldharbour Heating & Air Henderson is not affiliated with, sponsored by, or authorized by Trane. We’re an independent shop that services the brand because so many Henderson homeowners own one.

How Trane Products Fail – and How We Fix Them

Trane builds a solid furnace, but every brand has its patterns. Here’s what we see again and again on Trane equipment in the Henderson valley, and how we handle each one.

  • Hot-surface igniter failure on the XR80 and XR90. The silicon nitride igniter is the most common no-heat call we get on these single-stage models. In Henderson’s dry air and dusty spring conditions, the igniter element gets coated and cracks, and the furnace goes through its sequence and shuts down without lighting. We test resistance, confirm the board is sending voltage, and replace with a Trane-spec igniter. Most igniter jobs run $150 to $280, parts and labor included.
  • Flame sensor fouling on the S9V2 and S9X2. These variable-speed two-stage furnaces are sensitive to a dirty flame sensor. The symptom is short cycling: the burner lights, runs 30 to 60 seconds, and drops out. It’s rarely the sensor itself going bad; it’s usually a slightly rich burn or a buildup that needs cleaning along with a combustion check. We clean, test microamps, and verify the gas pressure is where Trane’s spec calls for it, not just swap the part.
  • Inducer draft motor wear on the XV80 and older XL90 units. On the aging Trane fleet around Henderson, the inducer motor bearing is a frequent failure. You’ll hear a rattle or hum at startup, and the pressure switch won’t prove, so the furnace never fires. We check the pressure switch tubing for cracks and blockage first, because that’s a $15 fix, before we recommend a motor.
  • Control board and igniter interaction on variable-speed models. On S9-series furnaces, a failing control board can mimic an igniter problem. If we see voltage at the igniter that drops or flutters, we know the board is the culprit, not the igniter. This is where swapping parts blindly gets expensive and a proper diagnostic saves real money.
  • Heat exchanger cracks on older Trane furnaces. On pre-2010 Trane units in Henderson, we inspect the heat exchanger every visit. A cracked exchanger is a carbon monoxide risk, and we’ll shut the furnace down and tell you plainly if it’s unsafe to run. Sometimes it’s a repair; often on a furnace that old, it’s the moment to talk replacement honestly.
Explore

Styles & brands we work with

  • AC repair
  • Furnace & heating
  • Heat pumps
  • Ductless mini splits
  • Carrier
  • Trane
  • Goodman

Our Trane Furnace Repair Process

Every Trane job follows the same five steps, and the price is set before step three.

  1. 1
    You call, a live person answers. No voicemail tree, no after-hours runaround. We book you a firm arrival window and stick to it.
  2. 2
    Full diagnostic on arrival. We check the thermostat call, the ignition sequence, gas pressure to Trane’s spec, inducer draft, flame sensor microamps, and the heat exchanger. We tell you what we found and what it will take to fix it.
  3. 3
    Written price before any work. OEM Trane part or a quality aftermarket equivalent, the trade-off explained in plain terms, and the number on paper. The price doesn’t change at the door.
  4. 4
    The repair itself. Done right, with the right part for your model, and no shortcuts on safety checks.
  5. 5
    Full test and a written 365-Day Done Right Promise. We run a complete heat cycle, confirm safe operation, and hand you a written guarantee: if this repair fails within 365 days, we come back and fix it at no charge.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

What Trane Furnace Repair Costs in Henderson

Here’s what the common Trane furnace repairs run in Henderson, parts and labor included. These are the ranges we quote, not a teaser number.

Repair Typical Cost
Trane igniter replacement $150 – $280
Flame sensor clean/replace $150 – $240
Gas valve repair or replacement $350 – $650
Blower motor repair or replacement $300 – $700
Inducer draft motor $280 – $550
Control board replacement $350 – $700
Full furnace tune-up $80 – $200

What moves the price: whether it’s a single-stage XR80 or a variable-speed S9V2 with more electronics, OEM versus aftermarket parts, and whether we’re chasing an intermittent issue that needs extra diagnostic time. You get a free estimate and the written price before we start. Call (844) 797-5122.

Why Henderson Homeowners Call Coldharbour Heating & Air Henderson for Trane Work

Most of our Trane calls come from homeowners who’ve been burned before: a no-show, a price that jumped at the door, or a repair that quit inside a month. That’s the reason we put our promises in writing. Every repair carries the 365-Day Done Right Promise. The written price is in your hands before the work starts. And a live person answers the phone around the clock, every day of the year.

Our technicians have up to 23 years of experience and are trained on nine major residential brands, so if your neighbor’s Carrier or Lennox needs help too, we handle it. But Trane is one we know cold, down to the model lines and their quirks. This is The Kingswell Way: say the price before the work, show up in the window we gave, leave the place cleaner than we found it, put the guarantee in writing, and come back if it fails. Coldharbour Heating & Air is an independently owned and operated member of the Kingswell network, founded in 2003.

FAQs

Need HVAC help nationwide? Licensed & insured · within the hour response · free estimates
Call (844) 797-5122
Local Service Coverage

Request a Free Estimate in Henderson

Tell us what you need - Coldharbour Heating & Air Henderson responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch